Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
I have a Model 5-75 insinkerator garbage disposal that is hard I have a Model 5-75. When I flip the switch to run the unit, there is a sound as if the motor is engage but does not spin. Fixing a Jammed Disposal. InSinkErator ma y pay to have an authorized service center service the disposal in your home at no charge to you.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
The list of things a food disposer can consume is fairly short. Soft or crisp foods are fine, but hard or stringy foods can be trouble. Disposers can be stopped in their tracks by celery, eggshells and apple seeds, as well as the usual kitchen flotsam, including pop-tabs, scouring pads and twist-ties.
Jamming is so common that every disposer comes with a wrench and an on-board circuit breaker, so don't assume your disposer has failed simply because it stops working. Use a flashlight to check for foreign objects lodged in the perimeter openings of the drum. Remove any obstruction with needle-nose pliers.
If you see nothing obvious, insert the wrench into the motor spline, found at the bottom of the unit, and twist right and left. If the motor spins freely, check that the circuit breaker hasn't tripped and then try the reset button. Descargar windows xp sp3 professional gratis en espanol full serial. If these measures don't work, and your disposer's warranty has expired, it's time to replace it.
Shopping For Disposals
Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.
We chose an In-Sink-Erator Pro SS (In-Sink-Erator, Division of Emerson Electric Co., 4700 21st St., Racine, WI 53406; www.insinkerator.com). The Pro SS has a stainless steel grinding chamber, a reversing 3/4-hp motor and a 5-year warranty. It sells for around $225.
Step 1: Turn Off Electricity
Begin by shutting off electricity to the unit at the service panel. Remove the cover from the base of the disposer, loosen the ground screw and remove both wire connectors
Step 2: Loosen the Bolts
Next, loosen the hose clamp on the dishwasher discharge hose and pull the hose from its fitting. To undo the drain crosspiece, loosen the bolts that bind the drain flange to the disposer.
Step 3: Remove the Old Unit
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
Step 4: Apply Putty
To install the new drain assembly, first roll a mound of plumbers putty on the counter until you have a 1/2-in.-thick, 10-in.-long piece. Stick this putty around the underside of the drain and press the drain firmly into the sink hole.
Step 5: Finish the Drain
To finish the drain assembly, slide the cardboard washer and backup ring onto the drain spud.
Step 6: Snap the Ring
Follow with the mounting flange and retaining ring. Snap the retaining ring onto the drain spud.
Step 7: Tighten
Tighten the bolts with a slotted screwdriver until most of the putty squeezes out and the drain feels snug in the sink.
Step 8: Wire It Up
It's usually easier to wire the new disposer before you install it. If the old installation was made without flexible conduit, now is the time to upgrade.
Begin by threading the old box connector into the base of the new disposer.
Step 9: Finish It Up
Bring the circuit wires and conduit into the connector and secure the conduit. Join the black circuit wire and black lead in one wire connector, and the white circuit wire and white lead in another. Bind the circuit ground wire under the green ground screw and replace the cover.
Step 10: Installing the New Unit
New disposers come with a dishwasher discharge nipple in place, but the nipple comes plugged in case you don't have a dishwasher. If you intend to use the dishwasher fitting, poke the plug out with a screwdriver and reach into the disposer to retrieve it.
Step 11: Installing the New Unit
Lift the disposer up to the sink drain and engage the tabs of the mounting ring. When you have the ring started, slip a screwdriver into one of the tab slots and rotate the ring clockwise until it bottoms out.
Step 12: Installing the New Unit
Insinkerator Model 75 Installation Manual Pdf
To plumb the disposer's drain outlet, fit the rubber washer over the flanged end of the plastic crosspiece, then slide the metal flange on from the other end. Tip the bottom of the metal flange into its slot in the disposer and tighten the fastening bolt through the top of the flange.
Step 13: Installing the New Unit
Winchester Model 75
Trim the crosspiece to length, connect it to the drain tee and install the P trap.
Insinkerator Model 75
Compact in size, the InSinkErator Evolution SpaceSaver 5/8 HP Continuous Feed garbage disposal is a powerful and quiet solution for those with limited cabinet space under the sink. The noise-insulated garbage disposer features a 5/8 HP Dura-Drive® Induction Motor for quiet operation and long life. With a 1725 RPM motor and Continuous Feed, the kitchen garbage disposer effectively handles large amounts of food waste.SoundSeal® Technology delivers Ultra-Quiet performance, making it possible to have a normal conversation by the sink while your kitchen garbage disposal is working. It uses anti-vibration technology, sound-reducing insulation, and a special Quiet Collar® sink baffle to block noise from coming up through the sink opening.MultiGrind® technology provides 2 stages of grind rather than 1 stage like standard disposers, to effectively grind difficult food items like bones. The kitchen garbage disposal has a substantial 34.6 Oz. capacity grind chamber that allows you to dispose of food waste right into the sink, keeping the food preparation area clean and reducing the amount of bagged garbage cluttering your kitchen. Built rugged, the stainless steel components provide superior durability and protect against corrosion. This InSinkErator garbage disposal has a patented Quick Lock® mounting system for easy installation and replacement of garbage disposers. The Quick Lock® mount is completely compatible with all InSinkErator models. When it's time to upgrade or replace, simply twist off the old mount and twist on the new one. Includes garbage disposer, flange, stopper, Quiet Collar® sink baffle, Jam-Buster™ wrench, assembly components, Quick Lock® components and user's manual.